Search found 42 matches
- Sat Dec 12, 2020 6:49 pm
- Forum: Engines
- Topic: removing spark plugs.
- Replies: 12
- Views: 26394
Re: removing spark plugs.
I used AC plugs R42XLS.
- Sun Aug 23, 2020 5:55 am
- Forum: General Topics
- Topic: bridge steering not responding
- Replies: 7
- Views: 11581
Re: bridge steering not responding
Tom, Looks like you have the Hynautic steering like I do. I replaced the leaking seal on the lower helm recently, which involves disconnecting and taking the helm apart. The system needed to be purged after re-installation. I followed the instructions in the owner’s manual, also shown in this utube ...
- Wed May 06, 2020 1:05 pm
- Forum: Boat and Hull
- Topic: naulex flooring glue
- Replies: 1
- Views: 7023
Re: naulex flooring glue
You’re lucky to have the original flooring. I wasn’t able to find any.
If I was able to source some, I would have used the Nautolex recommended adhesive, which should still be available.
If I was able to source some, I would have used the Nautolex recommended adhesive, which should still be available.
- Wed Jan 08, 2020 9:18 pm
- Forum: Cabin and Interior
- Topic: exterior flooring suggestions needed
- Replies: 18
- Views: 39521
Re: exterior flooring suggestions needed
I ordered the Lonseal from a company named “Ameriteak” located in Carson City NV. I ordered a 6’w x 14’ long roll, which was enough to do the entire aft deck and hatch. I used 1/2 gallon of the #650 adhesive they suggested. The cost: Lonmarine # 370 6x14 roll: $553.86 # 650 adhesive: $ 59.00 My aft ...
- Tue Jan 07, 2020 11:16 am
- Forum: Cabin and Interior
- Topic: exterior flooring suggestions needed
- Replies: 18
- Views: 39521
Re: exterior flooring suggestions needed
I used 5/8” marine grade plywood and covered with “Lonseal” vinyl covering, holly and teak pattern.
- Tue Jul 30, 2019 8:36 am
- Forum: General Topics
- Topic: 1985 M 39 DC gas tank selector
- Replies: 6
- Views: 17005
Re: 1985 M 39 DC gas tank selector
On my 32, I noticed that the generator can only take suction on the starboard tank. That would also explain the tanks not going down evenly.
- Thu Jul 04, 2019 3:33 pm
- Forum: Engines
- Topic: LM 318 140 thermosts
- Replies: 9
- Views: 23034
Re: LM 318 140 thermosts
I got mine from Amazon:
https://www.amazon.com/dp/B00027GZXW/re ... hDb5TM35E3
https://www.amazon.com/dp/B00027GZXW/re ... hDb5TM35E3
- Sun Jun 23, 2019 8:44 am
- Forum: Engines
- Topic: Exhaust Manifold Options?
- Replies: 6
- Views: 19291
Re: Exhaust Manifold Options?
That may be able to be welded. I had one repaired at this place in Cleveland:
Guarantee Auto Weld Co Inc
216-431-1214
Guarantee Auto Weld Co Inc
216-431-1214
- Thu May 09, 2019 10:33 am
- Forum: Electrical and Electronics
- Topic: Ignition coil replacement?
- Replies: 1
- Views: 12626
Ignition coil replacement?
Both of the engines stall at low idle once the get warmed up. Usually right after I’m out running on the lake and the come inside the breakwall ready to dock. When I first start them, they idle fine. I’ve read in other posts that this could be caused by weak coils. I did a tune up on both engines an...
- Mon Oct 22, 2018 6:49 pm
- Forum: Cabin and Interior
- Topic: Under deck wood floor and "pegboard" type?
- Replies: 4
- Views: 16950
Re: Under deck wood floor and "pegboard" type?
Welcome! I used 5/8” marine grade plywood and covered with “Lonseal” vinyl covering. I was able to use the old pieces as patterns, and apply the covering at home, then drop them in and screw them back down in the spring.