Search found 229 matches

by EWRice
Thu Jun 21, 2018 4:39 pm
Forum: General Topics
Topic: Stern railing design
Replies: 15
Views: 264

Re: Stern railing design

I think they used 1/8" x 3/4" aluminum stock. They used aluminum on mine because it supported the canvas at the aft corners where there was no stanchion. It is all long gone now, and I like it better. Never had a problem getting wet though.
by EWRice
Tue Jun 05, 2018 7:27 pm
Forum: Props
Topic: Spacing between prop and rudder
Replies: 2
Views: 126

Re: Spacing between prop and rudder

My 32 has just enough room to sneak the prop off, if you tip it just right. That is original as far as I know. The 32 that I just re powered with 1.250 shafts was about the same. It had a little more room but only because the shafts were set up for castle nuts where mine are jam nuts. The castle nut...
by EWRice
Sat Jun 02, 2018 8:05 pm
Forum: About My Boat Brags
Topic: MY 1966 26 ft 327 fireball
Replies: 37
Views: 4053

Re: MY 1966 26 ft 327 fireball

Being that yours is flywheel forward there are two different water pumps. The impellers are the same (and same as the chryslers) but the actual pump casting is different from LH to RH rotation. I do have a few pumps but would need to know your engine rotation. Over their production, the rambler base...
by EWRice
Wed May 16, 2018 11:35 am
Forum: Electrical and Electronics
Topic: How do you make coffee at anchor?
Replies: 13
Views: 2344

Re: How do you make coffee at anchor?

I don't drink coffee, but my wife does. We don't have a generator either. We have a two burner propane stove and an old percolator. Wife says that makes the best coffee you can get.
by EWRice
Wed May 16, 2018 11:29 am
Forum: Boat and Hull
Topic: Do the Anodes have to be bolted to the hull or can they by glued?
Replies: 8
Views: 530

Re: Do the Anodes have to be bolted to the hull or can they by glued?

Bolted, welded, or you could glue them only if you had a bonding wire connected from the anode to the hull/rudder/tab/etc. Bolting is easiest.
by EWRice
Sat May 12, 2018 8:08 pm
Forum: Engines
Topic: Ceramic starter item
Replies: 6
Views: 276

Re: Ceramic starter item

That is your ignition ballast resistor. You must have electronic ignition. Sierra p/n 18-5451

I think the automotive ones are the same.
by EWRice
Thu May 10, 2018 9:03 pm
Forum: General Topics
Topic: Can I make a rudder using Aluminum?
Replies: 5
Views: 365

Re: Can I make a rudder using Aluminum?

The only boats I have ever seen with aluminum rudders are sailboats and kayaks. I would be willing to bet that a powerboat would bend the rudder stock over time from the prop wash if it was sized the same as a steel rudder. When I made my SS rudders, I used pieces from my old prop shafts for the sto...
by EWRice
Thu May 03, 2018 9:41 am
Forum: Through Hulls
Topic: Prop Shaft Seal question
Replies: 9
Views: 643

Re: Prop Shaft Seal question

You should only need the brand of seal and shaft diameter to order a replacement. Unless the hose/bellows needs to be replaced because of a tear. If my memory serves me right, the shaft log is 1.875" o.d.
by EWRice
Wed May 02, 2018 11:42 am
Forum: Boat and Hull
Topic: Bow Hatch
Replies: 15
Views: 1953

Re: Bow Hatch

Something I have considered, since I will be pulling my hatch out and blasting it, is to have the underside sprayed with a thin layer of closed cell foam, or urethane (think truck bed liner). I think the foam would work best and could be shaved down and painted to the point that it may only be notic...
by EWRice
Wed May 02, 2018 11:31 am
Forum: General Topics
Topic: 37 Sedan- Considering LARGER rudders, thoughts?
Replies: 9
Views: 534

Re: 37 Sedan- Considering LARGER rudders, thoughts?

First off, I can close my eyes and hear the sweet sound of those Cat V8s idling. Makes me smile. I bet they fire and idle quicker than you can let off the key. As far as the prop affecting steering, you would have to substantially increase diameter to affect steering. Almost to the point of longer s...

Go to advanced search