Search found 442 matches
- Mon Feb 11, 2019 12:05 pm
- Forum: Engines
- Topic: 360 valve cover gasket replacement
- Replies: 16
- Views: 1393
Re: 360 valve cover gasket replacement
BigM I have found over the years that the large bolt holding the oil filter bracket to the engine has a tendancy to losen over time. Simply tightern this has stopped a lot of my oil leaking into the bildge. :o The next culpert is the nipple at the rear of the engine where the oil sender and alarm se...
- Wed Jan 30, 2019 1:44 pm
- Forum: Boat and Hull
- Topic: Stress cracks ???
- Replies: 15
- Views: 1123
Re: Stress cracks ???

32' Fisherman with new rebuilt motors.




bill
- Wed Jan 30, 2019 12:35 pm
- Forum: Boat and Hull
- Topic: Alternator / Ignition / Ballast resistor questions from a dummy
- Replies: 6
- Views: 1175
Re: Alternator / Ignition / Ballast resistor questions from a dummy
BigM This is the wiring diagram for the 4 pin ECM. It shows the ballast resister is only used for the coil. Pin #3 is not used. On the 5 pin ECM pin #3 is feed from the 5.0 ohm side of the dual ballast resister. On both ECM's Pin #1 is feed from the ignition on side of the ignition switch at full ba...
- Wed Jan 30, 2019 12:34 pm
- Forum: General Topics
- Topic: Re: Line Drawing
- Replies: 10
- Views: 659
Re: Line Drawing

Thanks for the update.

I look around some of my old sites

Have you looked here

bill
- Wed Jan 30, 2019 10:48 am
- Forum: General Topics
- Topic: Re: Line Drawing
- Replies: 10
- Views: 659
Re: Re: Line Drawing

Okay I will bite.

What is a line drawing???

bill
- Thu Jan 17, 2019 3:36 pm
- Forum: Vendors
- Topic: coverting chrysler electronic ignition to a hei unit
- Replies: 0
- Views: 327
coverting chrysler electronic ignition to a hei unit

If you are interested in converting your ignition over to a simpler set up.

bill
- Thu Jan 17, 2019 3:16 pm
- Forum: Boat and Hull
- Topic: Alternator / Ignition / Ballast resistor questions from a dummy
- Replies: 6
- Views: 1175
Re: Alternator / Ignition / Ballast resistor questions from a dummy
BigM Food for thought. 8-) The original 5 pin ignition modules needed a ballast resister in order to reduce the voltage to the unit the newer 4 pin do not. They run on 12 volt. The old two ballast resister system was used to reduce the voltage to the module and the coil. If you switch to a four pin ...
- Wed Nov 28, 2018 6:19 am
- Forum: About My Boat Brags
- Topic: New Boater, New to me Marinette.
- Replies: 18
- Views: 3236
Re: New Boater, New to me Marinette.

Bob,
Thanks for the photos.

Were you able to get all the parts that the privious owner removed. Glass, wood, floors and etc..........

bill
- Thu Nov 15, 2018 12:19 pm
- Forum: About My Boat Brags
- Topic: New Boater, New to me Marinette.
- Replies: 18
- Views: 3236
Re: New Boater, New to me Marinette.

Welcome aboard.

bill
- Sun Nov 11, 2018 1:44 pm
- Forum: Boat and Hull
- Topic: Paint scheme
- Replies: 5
- Views: 1359
Re: Paint scheme

Black or Blue looks great with white.



bill