Search found 406 matches
- Wed Apr 11, 2018 12:45 pm
- Forum: Shafts
- Topic: Drive Savers
- Replies: 6
- Views: 18870
Re: Drive Savers
They are expensive but shop around. I found some places wanted twice as much as some others. --Ed
- Sun Apr 01, 2018 1:26 pm
- Forum: General Topics
- Topic: Main Station Lower Helm Restoration nearly complete...
- Replies: 6
- Views: 9750
Re: Main Station Lower Helm Restoration nearly complete...
Didn't know that they had a method to their madness when they made them. I just like it on the British side, that's what I'm used to.--Ed
- Sun Apr 01, 2018 1:21 pm
- Forum: Engines
- Topic: reverse rotation engines
- Replies: 27
- Views: 40370
Re: reverse rotation engines
The special starter spins the engine the other way, then the pistons come up to top dead center on the compression stroke in the reverse firing order, so then the firing order on the distributor is in the reverse order even though the rotor spins in the same direction. So it runs the other way. If y...
- Sat Mar 31, 2018 2:55 pm
- Forum: General Topics
- Topic: Main Station Lower Helm Restoration nearly complete...
- Replies: 6
- Views: 9750
Re: Main Station Lower Helm Restoration nearly complete...
Looks really nice but the helm is on the wrong side. Or did you reverse the negative?
- Sat Mar 24, 2018 1:25 am
- Forum: Paint
- Topic: Swim platform paint
- Replies: 3
- Views: 15864
Re: Swim platform paint
I think that powder coat would be the most durable if you can do it. Imron was just the first two part polyurethane, I think you will find there are better and much cheaper ones now. If you use any two part paint you mix, you have to have a supplied air respirator to spray it. There are no cartridge...
- Mon Mar 12, 2018 1:24 am
- Forum: General Topics
- Topic: Windshield Wiper Motor
- Replies: 2
- Views: 5662
Re: Windshield Wiper Motor
I got one off the shelf at my local NAPA which stocks a lot of boat parts. So they are still being made and easily available. I had to get the longest shaft they had, and it was still barely long enough. Message me if you can't find one.--Ed
- Sun Mar 04, 2018 4:06 pm
- Forum: Vendors
- Topic: Packing Boxes
- Replies: 11
- Views: 33912
Re: Packing Boxes
Would not even consider removing the struts unless you have to remove them for some other reason. This is one of the easier, simpler jobs. Just have the boat up high enough you can get under it safely. If it is on a trailer you can drop the tongue down to raise the stern. Jack stands are not safe en...
- Sun Feb 25, 2018 11:34 pm
- Forum: Boat and Hull
- Topic: Cutlass Bearing Size
- Replies: 10
- Views: 19447
Re: Cutlass Bearing Size
Mine are 1 inch shafts ( part named BETTY ) easy way to measure is grab a 1 inch open end wrench and see if it fits the shaft. If you don't have a 1 inch, then use a Crescent wrench and adjust it to be snug. Then measure the wrench.
- Fri Feb 23, 2018 1:01 pm
- Forum: General Topics
- Topic: Chicago boat show
- Replies: 9
- Views: 12896
Re: Chicago boat show
I have boat insurance with Progressive, they're good and I would recommend them. You might call 1-800-876-5581 and ask about the shirts. Flo will help you out.
- Sat Feb 10, 2018 2:11 pm
- Forum: Boat and Hull
- Topic: Source for 5/8" starboard marine anti slip
- Replies: 7
- Views: 13338
Re: Source for 5/8" starboard marine anti slip
I am very happy having aluminum on my deck. Can't find the pictures I have of the deck, but you can see some of it here. Mine is one big piece which makes it hard to remove, so I would recommend installing it in a couple of pieces.