Quite a boat!! Hope you're able to sell for at/close to asking price. It's worth it!
Question (as I already have a 32' and next (dreamer) purchase would be a 41' Marquis)... where did you find/buy the end table/drawer(s) unit in the salon between the white/aluminum deck chairs?
Thx,
Bill
Search found 507 matches
- Fri Sep 01, 2017 10:13 am
- Forum: For Sale or Wanted
- Topic: Sold 1988 Marinette Sedan
- Replies: 6
- Views: 7541
- Tue Aug 22, 2017 7:47 am
- Forum: Cabin and Interior
- Topic: Refrigerator Replacement
- Replies: 31
- Views: 89413
Re: Refrigerator Replacement
We used a Xantrex 1000W inverter. http://www.ase-supply.com/Xantrex_806_1010_PRO_Series_Inverter_p/xa-806-1010.htm It supplies plenty of affordable AC to the fridge (ours draws 74 watts when running). You'd need to check your fridge's current draw + normal run time as it cycles on/off to figure the ...
- Thu Aug 17, 2017 8:05 am
- Forum: General Topics
- Topic: jralbert Private message outbox stuck
- Replies: 7
- Views: 11460
Re: jralbert Private message outbox stuck
With MetalHead's notation above, you can use this as sort of a "message has been read" alert, similar to AOL's system for emails sent to other AOL members. A backdoor "email receipt".
Bill
Bill
- Thu Aug 10, 2017 9:16 am
- Forum: General Topics
- Topic: Pumping out your holding tank
- Replies: 11
- Views: 16442
Re: Pumping out your holding tank
I'd rather think of you, Jeff, as the "Epitome of Frugality"!!
Bill
Bill
- Wed Aug 09, 2017 8:45 am
- Forum: Engines
- Topic: 1988 lm318 carburetor
- Replies: 17
- Views: 24389
Re: 1988 lm318 carburetor
I'm concerned....
... flippin' the rotor so many times could cause cramping...
... best to stop every few " flips " snd re-exercise the fingers/hand...
... grabbing a brewski should work quite well!!!
And in doing so should keep the "flipper" well oiled as well.
Bill
... flippin' the rotor so many times could cause cramping...
... best to stop every few " flips " snd re-exercise the fingers/hand...
... grabbing a brewski should work quite well!!!
And in doing so should keep the "flipper" well oiled as well.
Bill
- Tue Aug 08, 2017 8:00 am
- Forum: Vendors
- Topic: Sea Hawk Bottom Paint REVIEW
- Replies: 5
- Views: 17030
Re: Sea Hawk Bottom Paint REVIEW
:| Hope I get better results with the Micron CF. Painting the bottom with a coat of white and then a coat of black. Boat's on blocks and won't go into water (Ohio River) till next spring. Will "back pocket" the info on Sea Hawk bottom paint when she's next pulled from water in fall 2018 an...
- Fri Jul 28, 2017 10:02 am
- Forum: Engines
- Topic: dip stick for 318
- Replies: 7
- Views: 12886
Re: dip stick for 318
I can measure length when I'm next at boat, or if someone else can...?
Only wrinkle will be at upper end's end.
Bill
Only wrinkle will be at upper end's end.
Bill
- Fri Jul 28, 2017 7:57 am
- Forum: Boat and Hull
- Topic: Retrofitting bow anchor platform
- Replies: 11
- Views: 22148
Re: Retrofitting bow anchor platform
Busia, (If you're still alive... :-D ), great story!! I use a plastic ammo box attached to the entrance to the chain/rode locker. I only use 15' of chain attached to my rode which seems to be sufficient to keep the anchor on the bottom and set well. Cutting a hole on each long side of the box allows...
- Fri Jul 28, 2017 7:51 am
- Forum: For Sale or Wanted
- Topic: insurance providers
- Replies: 13
- Views: 21638
Re: insurance providers
We use Geico Marine Insurance (used to be Seaworthy). Good rates.
https://login.seaworthyinsurance.com/SI ... Login.aspx
Bill
https://login.seaworthyinsurance.com/SI ... Login.aspx
Bill
- Mon Jul 24, 2017 10:43 am
- Forum: Boat and Hull
- Topic: transom gate and swim platform
- Replies: 24
- Views: 35396
Re: transom gate and swim platform
Jeboniface,
Thanks for posting the pics. Nice work and great detail. Did you need to special order the aluminum channel across the top of the gate?
Bill
Thanks for posting the pics. Nice work and great detail. Did you need to special order the aluminum channel across the top of the gate?
Bill