Aft Deck Restoration

Corrosion, Paint, Through Hulls, etc.
DougDoty
Tin star
Posts: 76
Joined: Fri Jul 11, 2014 9:26 pm
Location: Madison In.

Re: Aft Deck Restoration

Postby DougDoty » Thu Apr 13, 2017 12:51 pm

I am 260 lb and do not think my original 5/8" decking feels at all springy. I have replaced the hatch and the section forward of it thus far. My hatch had gotten rotten and the section in front of it was beginning to sag in the middle over time and held water. in a pool. I need to do the three remaining sections still, they are not soft anywhere but have holes from mounted fishing chairs and down riggers.
1984 39 Marinette Sedan, " LIBERTY ONE " Warsaw KY, 440 chryslers, Westerbeke 9.0 kw , 1 3/8" shafts 93 1/4" long and 19x22 dyna quads or, 19x20 DQX's 38.5 MPH GPS best.

Joe
Tin star
Posts: 53
Joined: Wed Jul 16, 2014 6:43 am

Re: Aft Deck Restoration

Postby Joe » Tue Sep 05, 2017 1:17 pm

Hello, I will be starting this winter on replacing the aft deck. Do you have any finished pics. I would like to see some different finished pic. Thanks Joe
1988 sedan flybridge. Black / White. 318 240 hp Aluminum aft deck hard top. Louisville Ky . Tartans landing. " KNOCKEFELLERS"

MetalHead
Site Admin
Posts: 203
Joined: Fri Jul 11, 2014 6:03 pm

Re: Aft Deck Restoration

Postby MetalHead » Wed Sep 06, 2017 4:21 am

Attachments
IMG_7108.JPG
IMG_7107.JPG
IMG_7106.JPG
21032899_1993531967594410_3476360875451901549_n.jpg
1959 Family Cruiser - Sold - Gary Dick - 12/05/14
1963 Express 31x10 - Sold - Joe & Ginger Tabor - 01/21/2017
1963 Express 31x8.5 - In Dry Dock - Restore Underway
1987 Sportsman - On Rolling Slip - Ready To Go !!!
Big BigM 's Rule !!!
Columbiana, AL

yooper
Aluminum Star
Posts: 105
Joined: Mon Jul 14, 2014 10:24 am

Re: Aft Deck Restoration

Postby yooper » Tue Sep 12, 2017 4:54 pm

Cut new plywood decking from 5/8" exterior plywood. Had a pickup bed sprayer spray and underlap the bottom side by 6". Replaced the big washer on the cockpit drains with a big 1/4" aluminium flage that fits under the corner side walls. Tighten the cockpit drain nut and the deck is tightened down in the corners. Only put back the under deck screws I could reach.

Joe
Tin star
Posts: 53
Joined: Wed Jul 16, 2014 6:43 am

Re: Aft Deck Restoration

Postby Joe » Sun Oct 22, 2017 5:16 pm

Hello trying to decide on what to use, on the aft deck . Has anyone used NAUTIFLOOR ? I was looking at the 65TE . I looked at plastek. I did not like the way it was glued together. I seen a swim platform with it. It did not hold up very well. I was going to go with starboard ,Butt the wife likes the look of the teak. Thanks Joe
1988 sedan flybridge. Black / White. 318 240 hp Aluminum aft deck hard top. Louisville Ky . Tartans landing. " KNOCKEFELLERS"

jralbert
Site Admin
Posts: 459
Joined: Fri Jul 11, 2014 9:15 pm

Re: Aft Deck Restoration

Postby jralbert » Sun Oct 22, 2017 11:36 pm

My plasteak bowsprit held up for years with no maintenance and always looked like new (was still going strong when I sold it). With more energy for a project, I would have covered rear deck with it. Mine was T&G (tongue and groove) - no glue. For the rear deck I would have used some kind of mfr-approved sealant in the groove where two pieces lock together.
-joel-
former owner 1988 '32 FB Sedan
Chesapeake Bay
twin 318 / 240 hp
Potomac MD