Window and Tint removal
-
- New poster
- Posts: 7
- Joined: Sun Apr 11, 2021 10:10 pm
Window and Tint removal
The tint on all of my windows is bubbling and looks terrible. How do I remove the windows so I can remove the window tint or replace the windows? Any suggestions or tips would be appreciated.
Jamey
1975 28 Express w318s
1982 32 Sedan FB w360s
1975 28 Express w318s
1982 32 Sedan FB w360s
Re: Window and Tint removal
Last edited by bill on Sat Jun 05, 2021 8:15 am, edited 1 time in total.
Former owner of
ALUMINATION
Grosse Ile MI
Located on LakeErie
37' F/B Sedan
1975
Twin 360 Chrysler Marine
Raw water cooled
Hydraulic steering both helms
USCG Master Lic. Retired[/color]
Third Owner bill
ALUMINATION
Grosse Ile MI
Located on LakeErie
37' F/B Sedan
1975
Twin 360 Chrysler Marine
Raw water cooled
Hydraulic steering both helms
USCG Master Lic. Retired[/color]
Third Owner bill
Re: Window and Tint removal
Hello, I made the same mistake using tinted film on my windows . It looked good for a couple of years but soon turn into a scratched bubbly mess.
Now would be a good time to think about installing the screen on the inside track.
This would requiring switching all port and starboard tracks
The tracks are held in place by flat head screws. Remove the three or four bottom screws.
Depending on who installed the tracks, maybe they used caulking? Caulk is highly recommended.
If so use a putty knife under the track and the aluminum edge it sets on. once the seal is separated slide both windows to center along with screen.
Another person would be a good idea for the next step.
Grasp the windows and screen on each end and slowly pull the lower track out while holding all the windows and screen together.
Slowly lower the package to the deck surface. I did this on my 37' by myself. Not recommended.
Note.
My tracks are original and are plastic. I took a sharp utility knife and removed just enough of the rib holding the glass and screen With the glass and screen centered in the opening. This enables me to remove the screen and the glass individually. If they are Aluminum tracks you could make a fixture and use a router to cut the center rib section out.
bill
Former owner of
ALUMINATION
Grosse Ile MI
Located on LakeErie
37' F/B Sedan
1975
Twin 360 Chrysler Marine
Raw water cooled
Hydraulic steering both helms
USCG Master Lic. Retired[/color]
Third Owner bill
ALUMINATION
Grosse Ile MI
Located on LakeErie
37' F/B Sedan
1975
Twin 360 Chrysler Marine
Raw water cooled
Hydraulic steering both helms
USCG Master Lic. Retired[/color]
Third Owner bill
-
- New poster
- Posts: 7
- Joined: Sun Apr 11, 2021 10:10 pm
Re: Window and Tint removal
Thanks Bill. I have some other issues to tackle with the engines first, but will give it a try! Appreciate it!
Jamey
1975 28 Express w318s
1982 32 Sedan FB w360s
1975 28 Express w318s
1982 32 Sedan FB w360s
Re: Window and Tint removal
Try pricking the bubbles with a tiny pin or sewing needle to let the air out,
-joel-
former owner 1988 '32 FB Sedan
Chesapeake Bay
twin 318 / 240 hp
Potomac MD
former owner 1988 '32 FB Sedan
Chesapeake Bay
twin 318 / 240 hp
Potomac MD
-
- New poster
- Posts: 7
- Joined: Sun Apr 11, 2021 10:10 pm
Re: Window and Tint removal
Thanks. That might help for temporary fix until I can get them all removed and replaced!
Jamey
1975 28 Express w318s
1982 32 Sedan FB w360s
1975 28 Express w318s
1982 32 Sedan FB w360s