Wind Screen for flybridge

Corrosion, Paint, Through Hulls, etc.
Post Reply
75Express
Tin star
Posts: 21
Joined: Sun Jul 13, 2014 6:14 pm

Wind Screen for flybridge

Post by 75Express »

Looking for the correct thickness, material type, length and width of the front and two sides.
My bought is missing it so i have nothing to compare
Thanks
1975 Express Flybridge 32
Twin 318
Lake Lanier, GA
Top
Fastjeff
Site Admin
Posts: 1535
Joined: Sat Jul 12, 2014 5:06 am
Location: Rock Halll, MD

Re: Wind Screen for flybridge

Post by Fastjeff »

Mine was smoked plastic about 1/4 " thick.

Jeff
"We live at the bottom of an ocean of air, not at the top." General Marvage Slatington
Top
User avatar
bill
Royal Aluminum Star
Posts: 521
Joined: Sat Jul 12, 2014 7:17 am
Location: Grosse Ile MI

Re: Wind Screen for flybridge

Post by bill »

75Express wrote:Looking for the correct thickness, material type, length and width of the front and two sides.
My bought is missing it so i have nothing to compare
Thanks
:?: It depends on the size of your boat.
28' :?: 32' :?: 37' :?: 39' :?: 41' :?:
That is why we use signatures :!:
See mine below :roll:
Bill
Former owner of
ALUMINATION
Grosse Ile MI
Located on LakeErie
37' F/B Sedan
1975
Twin 360 Chrysler Marine
Raw water cooled
Hydraulic steering both helms
USCG Master Lic. Retired[/color]
Third Owner bill
Top
75Express
Tin star
Posts: 21
Joined: Sun Jul 13, 2014 6:14 pm

Re: Wind Screen for flybridge

Post by 75Express »

Dang I guess I lost my signature with the new site

It is a 32 foot
1975 Express Flybridge 32
Twin 318
Lake Lanier, GA
Top
75Express
Tin star
Posts: 21
Joined: Sun Jul 13, 2014 6:14 pm

Re: Wind Screen for flybridge

Post by 75Express »

Thanks Fast Jeff
1975 Express Flybridge 32
Twin 318
Lake Lanier, GA
Top
75Express
Tin star
Posts: 21
Joined: Sun Jul 13, 2014 6:14 pm

Re: Wind Screen for flybridge

Post by 75Express »

Can anyone tell me how wide the plexiglass is? 6 inches?,7inches? 8"inches?
Thanks
Stan
1975 Express Flybridge 32
Twin 318
Lake Lanier, GA
Top
Joe
Tin star
Posts: 74
Joined: Wed Jul 16, 2014 6:43 am

Re: Wind Screen for flybridge

Post by Joe »

I have a set. Their off my 1988 32 .Their in my storage container. I could make a paper copy and send to you. I dont know if the later ones are the same. They are 1/4 inch. You need to use the right material . Or they will break. I made 3 set . The first 2 sets broke. Before you start. Take some of the plastic ,put it in a vice. and bend it over. If it breaks dont try to use it. If it bends ,and flexes back your good. . You will have approx 300.00 in material plus labor. Let me know Joe.
1988 sedan flybridge. Black / White. 318 240 hp Aluminum aft deck hard top. Louisville Ky . Tartans landing. " KNOCKEFELLERS"
Top
75Express
Tin star
Posts: 21
Joined: Sun Jul 13, 2014 6:14 pm

Re: Wind Screen for flybridge

Post by 75Express »

Thanks for the offer Joe. I would love to have a pattern to work from. If it is not to much trouble.
Stan
1975 Express Flybridge 32
Twin 318
Lake Lanier, GA
Top
Fastjeff
Site Admin
Posts: 1535
Joined: Sat Jul 12, 2014 5:06 am
Location: Rock Halll, MD

Re: Wind Screen for flybridge

Post by Fastjeff »

Whatever you do, DON'T use Plexiglass; Lexan is a far better material--it's not so damn brittle!

Jeff
"We live at the bottom of an ocean of air, not at the top." General Marvage Slatington
Top
Joe
Tin star
Posts: 74
Joined: Wed Jul 16, 2014 6:43 am

Re: Wind Screen for flybridge

Post by Joe »

Send me your address . knockwafel@twc.com I will send it to you. Joe
1988 sedan flybridge. Black / White. 318 240 hp Aluminum aft deck hard top. Louisville Ky . Tartans landing. " KNOCKEFELLERS"
Top
Post Reply

Return to “Boat and Hull”