Oil Pressure sensor.

Engines, Shafts, Steering, Struts, Rudders, etc.
wschneid
Tin star
Posts: 20
Joined: Sat Jul 18, 2020 1:10 pm

Oil Pressure sensor.

Postby wschneid » Tue Nov 17, 2020 6:17 pm

The starboard engine on my 32' FB with Chrysler 318's gets pegged to the right when I start the engine. Could this be a sign of a faulty oil pressure sensor? And where is the sensor located on that engine? The engine runs fine, but the oil pressure showing that high concerns me.

Bill Schneider

Fastjeff
Site Admin
Posts: 1320
Joined: Sat Jul 12, 2014 5:06 am
Location: Rock Halll, MD
Contact:

Re: Oil Pressure sensor.

Postby Fastjeff » Wed Nov 18, 2020 6:45 am

That might be an accurate oil pressure reading if the relief valve in the oil pump is stuck closed.

I would stick a second oil pressure gage on it temporarily and see if that gage went way up as well.

Jeff

PS: If I'm righ you should change the oil immediately.
"We live at the bottom of an ocean of air, not at the top." General Marvage Slatington

User avatar
bcassedy
Royal Aluminum Star
Posts: 415
Joined: Sun Jul 13, 2014 10:05 am
Location: Aurora, In.
Contact:

Re: Oil Pressure sensor.

Postby bcassedy » Wed Nov 18, 2020 7:41 am

The location of the oil pressure switch is at the rear of the engine. Back in 2018 I was going to switch to an electronic gas pump. Part of the process requires an oil pressure switch be electrically in line to the pump so that, if the engine should die (or just the ignition be left energized - engine not running) the oil pressure switch would open, breaking the circuit to the gas pump (and preventing a flood of gas spewing from the carb - bad thing! :roll: ). This is a pic of the "stack" of pressure switches. Your original one would be first (second?). The 3rd (top - canister) is the one I added - but ultimately didn't need as I located a source for the mechanical pump and used that.
Strbrd oil pressure swtch stack - 50% of 25%.jpg


Note - I did try removing the original switch but it seemed I'd foul up the threading / break off the original switch in the process. Opted to just "stack" the new one, which has worked well (it's just sitting there, not being used - the engine, other oil switches below, and gauge don't seem to care.
Bill
Last edited by bcassedy on Wed Nov 18, 2020 2:15 pm, edited 1 time in total.
Bill & Sharon Cassedy
"Sunset Seeker"
'88 32' Sedan Bridge
Located in Aurora, In.
Twin 318cu in Chrysler
1.5:1 Velvet drive trannies
Fresh water only

jralbert
Site Admin
Posts: 753
Joined: Fri Jul 11, 2014 9:15 pm

Re: Oil Pressure sensor.

Postby jralbert » Wed Nov 18, 2020 12:52 pm

In this discussion of oil press switches one thing to add. They are failure prone. Oil will shoot out. Maybe it's vibration - I don't know. Check them often and have a spare or two on hand. If one were to let go on a trip, you'd lose vital oil quickly. Which is why one monitors oil press and temp and have a temp alarm.
-joel-
former owner 1988 '32 FB Sedan
Chesapeake Bay
twin 318 / 240 hp
Potomac MD

ddependo
Royal Aluminum Star
Posts: 282
Joined: Mon Jul 14, 2014 10:00 am

Re: Oil Pressure sensor.

Postby ddependo » Fri Nov 20, 2020 7:31 am

Good point, to have a couple of spares. Anyone have the part # for 318 engines?
Thanks, Wayne
1973 32 express fly bridge
Chattanooga
"Southern Lady"

User avatar
Tuggle
Aluminum Star
Posts: 157
Joined: Sun Jun 26, 2016 4:42 am

Re: Oil Pressure sensor.

Postby Tuggle » Sun Nov 22, 2020 4:59 am

Check your ground, inspect the wire, clean the terminals.
"Deplorable", 1975 32' Express, Twin 318's, Raw Water Cooled, Lake Lanier, Ga.

javalin390
Royal Aluminum Star
Posts: 333
Joined: Sat Jan 10, 2015 7:14 pm
Contact:

Re: Oil Pressure sensor.

Postby javalin390 » Wed Nov 25, 2020 6:40 pm

Also note that if you have more than one switch, one of course for the gauge, one for the engine alarm, if equipped, and possibly another for engine shut-down, as in the case of boats with electric fuel pumps OR this same switch was originally used to complete the field circuit on the old style Chrysler voltage regulator.
#3619738 or 4417702 - this is the simple, small on/off oil switch for engine alarm, voltage regulator, or fuel pump shut off. NAPA carries hundreds of different switches so I'm certain they can match it up (most use the same threads).
#3619101 - for gauge
#3527242 - for gauge--both of these part numbers are listed in the Chrysler parts manual, and depends on a certain engine option, but I'm not sure what that engine option is.
#3619617 - for gauges (2), this one is used on dual helm boats and will not read correctly if used on a single helm ( not sure if it will read double or read half)
#R020006 - this is also a dual helm sender from Crusader Marine, interchanges with Chrysler 3619617.
Once again, NAPA or a speed shop (i.e. Jegs, Summit Racing) could probably cross them into a newer, available part number depending on the brand of gauges you have and the ohm range (a common ohm range is 0-90).
Hope this helps.
Jim Elias
1974 37' SedanFlybridge
Twin 360 Chryslers.
Marblehead, Ohio